YA206 Engine Diagnostic Trouble Code Reader 12V with OBD2 Full Functions

Can YA206 Remove Error Engine Light ?

Of course, OBDII Code Reader YA206 Supports to remove car engine light ,which has problem on the car OBDII emissions.

1.Turn Off ''Check Engine'' Light
Parts cause your check engine light on include:
1. Gas Cap 2. Oxygen Sensor 3. Air Fuel Ratio Sensor
4. Mass Air Flow Sensor 5. Ignition Coils 6. Spark Plug Wires
7. Spark Plugs 8. Thermostat 9. EGR Valve
10. Evaporatative Emission Canister Purge Valve(EVAP) 11. Catalytic Converter.

2.Decreased fuel consumption,Decreased engine noise.?Decreased in temperature , ect .
If the engine light is not turned off in time.it will Cause Serious environmental pollution

Have you set these situation ?

1. Spend too much time to go to dealer workshop ?
2. Failure to find the vehicle problem in time ?
3. Hard to find where the problem is ?
4. Difficult to find the problem due to the complex structure?

What's OYA206 Engine Diagnostic Trouble Code Reader 12V?

OBDII Code Reader YA206 is a versatile car fault diagnosis instrument with reading fault code, clearing fault code and supporting multi ECU module battery. Detection, screen capture and other functions. The product is stable, cost-effective, easy to operate and easy to use. Suitable for owners without maintenance experience, not only save maintenance time and money, but also imp-rove the safety factor of driving.

Why Choose the OBDII Code Reader YA206?

1. Support full OBDII diagnostic functions.
2. Multi-Languages: English, Russian, German, Spanish, French, Italian, Portuguese, Japanese, Chinese
3. No need to register.
4. Free Update Lifetime: Just Put in the USB, Copy and Paste the files into Flash disk .

5. Screenshut function: Press the up and down button together for about 3 seconds. It will help you to record the data .

6. YA206 supports Data stream sorting
7. Voltage Test : This function is used to monitor the voltage present on pin 16 of the OBDIIData Link Connector.
8. Supports Battery Tester Function

9. In live data menu, you can insert the selected item to front by holding pressing the "ok" key for 3 seconds

The Function of YA206 Engine Diagnostic Trouble Code Reader 12V

1. Accurately detect the cause of the engine fault light in order to solve or clear the problem with the car.
2. One key to read or clear fault code.
3. Turn off the engine warning light by clear the fault code.

YA206 Supports Full OBD2 Functions, Engine Check Including:

●Reading Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs)
●Erasing Codes & Reset: Turns off Check Engine Light (MIL), clears codes and resets monitors.
●Data Stream: Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.
●I/M Readiness Status: Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.
●Read Live Data Stream: Show the information of continuous data stream from a vehicle in live graphic (waveform) display.
●View Freeze Frame Data: Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.
●O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.
●On-Board Monitor Test (Mode 6): Retrieves and displays test results for emission-related powertrain components and systems.
●Read Vehicle Information: Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.
●Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability

Support Car Models for OBDII diagnostic function:

American Car : Standard OBD2 Protocols from 2000 to now;
European Car : Standard OBD2 Protocols from 2003 to now;
Japanese/Korean Car: Standard OBD2 Protocols from 2006 to now.

Where to check if my car OBD2 compliant?

This is a diagnosic scanner work based on Legislated OBD-II protocols:

ISO15765-4 (CAN)
ISO14230-4 (Keyword Protocol 2000)
ISO9141-2 (Asian, European, Chrysler vehicles)
J1850 VPW (GM vehicles)
J1850 PWM (Ford vehicles)

If you are not sure, look under the hood and try to locate a label that explicitly states that the vehicle was designed to comply with OBD2 legislation.

In this case, OBDII is used as a general term and can mean any of the following:

OBD II (California ARB)
EOBD (European OBD)
JOBD (Japanese OBD)

You may also consult your vehicle's owner's manual and perhaps contact your local dealer. However, be aware of the fact that many dealers do not know the difference between OBD and OBDII.

If the vehicle is not OBD-II compliant, you cannot use this OBD2 scan tool to obtain diagnostic information from your vehicle.

OBDII Code Reader YA206 Specifications:

Screen: 2.4 inch TFT colordull screen, 320*240 resolution
Keyboard: 4pcs keyboard ( Up, Down, Back, Enter/Confirm )
Voltage Range: 9-18V
Operating Temperature :0℃ -50 ℃ (32 ℉ -122 ℉ )
Environment Temperature -20 ℃ -70 ℃ (-4 ℉ -158 ℉ )
Dimension :125mm*70mm*22mm(4.65" *2.68 " *0.88 " )
Weight: 200g

Notice of I/M Readiness:

* To review I/M Readiness status,make sure that the ignition key is switched to ON with the engine off.
* Not all monitors are supported by all vehicles.There are two types of l/M Readiness tests:
* since DTCs Cleared -shows status of the monitors since the DTCs werelast cleared.
* This Drive Cycle-shows status of monitors since the start of the currentdrive cycle.

Packing List:

1pc * OBDResource YA206 Code Reader 12V
1pc * English User Manual

Guarantee

OBDResource Official Store provided 15 Days return and full technical support, if any problems, please kindly contact us for support service.

Questions & Answers:

●Question: How to verify whether the vehicle will pass the emission test with this code reader?
Answer: After entering the I/M Readiness, there will be 10 results on the list. Misfire monitor, fuel system, componentmonitor, catalyst monitor, heated catalyst, EVAP system, secondary air sys, 02 sensor, O2 sensor heater EGRand/or WVT. There will be an OK if each of them works fine. [Not all vehicles have these 10 parts]

●Question: System halts when reading data stream. What is the reason?
Answer: It may be caused by a slackened connector. Please turn off the tool,firmly connect the connector, and switch it on again.

●Question: Screen of main unit flashes at engine ignition start.
Answer: Caused by electromagnetic disturbing, and this is normal phenomenon

●Question: There is no response when communicating with on-board computer.
Answer: Please confirm the proper voltage of power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is in proper temperature.

●Question: Why are there so many fault codes?
Answer: Usually, it’s caused by poor connection or fault circuit grounding

●Question: Does it support read and clear ABS Airbag error?
Answer: No,it only read engine error

YA102 Check Engine Error Code Reader Specifications:

Screen: 1.8 inch TFT colordull screen, 160*120 resolution
Keyboard: 4pcs keyboard ( Up, Down, Back, Enter/Confirm )
Voltage Range: 9-18V
Operating Temperature :0℃ -50 ℃ (32 ℉ -122 ℉ )
Environment Temperature -20 ℃ -70 ℃ (-4 ℉ -158 ℉ )
Dimension :125mm*70mm*22mm(4.65" *2.68 " *0.88 " )
Weight: 0.175kg

Notice of I/M Readiness:

* To review I/M Readiness status,make sure that the ignition key is switched to ON with the engine off.
* Not all monitors are supported by all vehicles.There are two types of l/M Readiness tests:
* since DTCs Cleared -shows status of the monitors since the DTCs werelast cleared.
* This Drive Cycle-shows status of monitors since the start of the currentdrive cycle.

Support Car Models for OBDII Diagnostic Function:

(Note: YA102 only Support 12V Gasoline & Diesel, Does not support 24V Truck )

American Car :
Need Standard OBD2 Protocols from 2000 to now
for Chrysler , for Ford, for GM, For Jeep ...

European Car :
Need Standard OBD2 Protocols from 2003 to now
For Alfa romeo , for SAAB ,for Acura , for Opel , for Audi for Seat , for Peugeot , for Renault
For Bentley , for Skoda , for Daewoo , for Benz , for Daihatsu , for Land Rover , for BMW , for Vauxhall , for Citroen , for Volvo , for Fiat , for VW , for Ford , for Jaguar...

Japanese/Korean Car:
Need Standard OBD2 Protocols from 2006 to now
for KIA, for Isuzu, for Honda , for Mitsubishi, for Hyundai , for Dacia , for Lexus , for Mazda, for Nissan, for Subaru , for Suzuki, for Toyota...

Check Engine Error Code Reader YA102 Support OBD 2 protocols car :

ISO15765-4 (CAN)
ISO14230-4 (Keyword Protocol 2000)
ISO9141-2 (Asian, European, Chrysler vehicles)
J1850 VPW (GM vehicles)
J1850 PWM (Ford vehicles)

OBD-II Compliant

If you are not sure, look under the hood and try to locate a label that explicitly states that the vehicle was designed to comply with OBD2 legislation.

In this case, OBDII is used as a general term and can mean any of the following:

OBD II (California ARB)
EOBD (European OBD)
JOBD (Japanese OBD)

If the vehicle is not OBD-II compliant, you cannot use this OBD2 scan tool to obtain diagnostic information from your vehicle.

YA102 Supports Full OBD2 Functions (For Engine System) Including:

●Reading Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs)
●Erasing Codes & Reset: Turns off Check Engine Light (MIL), clears codes and resets monitors.
●Data Stream: Reads and displays live ECU/PCM data stream, stores freeze frame data.
●I/M Readiness Status: Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.
●Read Live Data Stream: Show the information of continuous data stream from a vehicle.
●View Freeze Frame Data: Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.
●O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.
●On-Board Monitor Test (Mode 6): Retrieves and displays test results for emission-related powertrain components and systems.
●Read Vehicle Information: Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.
●Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability

8. Option:
Changes tool option displays tool information, and performs tool self-tests.
9. Unit:
Changes measurement units display metric or imperial.
10. Data Logging:
Turn on /off the data log function to record the device data through vehicle.
11. Self-test:
Display Test . Used to check the display screen.
12. Keyboard Test :
Verifies that the keys are working correctly.
13. Easy to Carry:
The OBD2 scanner's mini size fits comfortably in the palm of your hand. so that you can carry it around no matter in garage or on a trip.

7. Battery Voltage Test :
This function is used to monitor the voltage present on pin 16 of the OBDII Data Link Connector.
Knowing ahead of your vehicle's battery status

6. DTC Look Up:
Looks up definitions of DTCs stored in scan tool, and shows the possible causes of the DTC. (Not every DTC with possible causes reason)

5. Screenshot function:
You can press "UP" and "DOWN" buttons simultaneously on this scan tool for 5 seconds to take a screenshot of your viewing data stream and storage inner.

3. No need register.
4. Free Update Lifetime:
Just connect with laptop, Copy and Paste the files into removable disk.

Why Choose the Check Engine Error Code Reader YA102?

1. Support full OBDII diagnostic functions.
2. Multi-Language:
English, Russian, German, Spanish, French, Italian, Portuguese, Japanese, Chinese

What's Check Engine Error Code Reader YA102?

YA102 is a versatile car fault diagnosis instrument with reading fault code, clearing fault code and supporting multi ECU module battery. Detection, screen capture and other functions. The product is stable, cost-effective, easy to operate and easy to use. Suitable for owners without maintenance experience, not only save maintenance time and money, but also imp-rove the safety factor of driving.

Have you met these situation ?

1. High cost from dealer
2. No warranty from workshop
3. No professional yourself

Can YA102 Remove Engine Warning Light ?

Of course, YA102 Supports to remove car engine light,, which has problem on the car OBDII emissions.

1) Turn Off ''Check Engine'' Light
Parts cause your check engine light on include:
1. Gas Cap
2. Oxygen Sensor
3. Air Fuel Ratio Sensor
4. Mass Air Flow Sensor
5. Ignition Coils
6. Spark Plug Wires
7. Spark Plugs
8. Thermostat
9. EGR Valve
10. Evaporatative Emission Canister Purge Valve(EVAP)
11. Catalytic Converter.

2) Decreased fuel consumption; Decreased engine noise; Decreased in temperature , ect .
If the engine light is not turned off in time.it will Cause Serious environmental pollution

Questions & Answers:

Questions & Answers:
Question: No connection with my car.
Answer: First, please check if your car is 12 Volt obd2 protocal, if yes, please send us the log file: Connect the YA102 with car, put car ignition on, choose Settings -- Data Logging -- On, and then start to testing your car. please plug out the YA102 when can't test the car. And then connect with laptop, copy the file on Data logging , send the file to us. Thanks

Question: Why the YA102 shows upgrading?
Answer: It will always shows upgrading when you connect with laptop.Please do not worry.

Question: How to verify whether the vehicle will pass the emission test with this code reader?
Answer: After entering the I/M Readiness, there will be 10 results on the list. Misfire monitor, fuel system, componentmonitor, catalyst monitor, heated catalyst, EVAP system, secondary air sys, 02 sensor, O2 sensor heater EGRand/or WVT. There will be an OK if each of them works fine. [Not all vehicles have these 10 parts]

Question: System halts when reading data stream. What is the reason?
Answer: It may be caused by a slackened connector. Please turn off the tool,firmly connect the connector, and switch it on again.

Question: Screen of main unit flashes at engine ignition start.
Answer: Caused by electromagnetic disturbing, and this is normal phenomenon

Question: There is no response when communicating with on-board computer.
Answer: Please confirm the proper voltage of power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is in proper temperature.

Question: Why are there so many fault codes?
Answer: Usually, it’s caused by poor connection or fault circuit grounding

Question: Does it support read and clear ABS Airbag error?
Answer: No,it only read engine error

Packing List:

1pc * OBDResource YA102 Code Reader
1pc * English User Manual