Car Windshield Repair Kit Tools Auto   Quick Fix Car Cracked Glass Repair Fluid  Resin Sealer DIY Auto Window Screen Polishing
Features:

Allows anyone to fix a damaged windshield or window.
Single ingredient - eliminates mixing.
Creates an invisible, undetectable repair in damaged automobile windshields or other laminated glass for windows.(Icludes instructions.)
DIY windshield repair kit is designed to fill the air cavity with a strong penetrating adhesive that will bond the loose glass and restore the visibility.
The patented design evacuates the air to fill the cavities with specially formulated liquid glass,that distortion and bonds the loose glass preventing the damage  from spreading.
Size: 10.3cm(Length) ,5cm( Diameter )
Weight: 28g
Material :Plastic & Rubber

Note:

Avoid using in direct sunlight-work in shaded area.
Do not work on a hot windshield, park vehicle in shaded area and open for windows to cool glass surface.
A safety razor is required to remove components and finsh repair.
Do not let resin come in contact with painted surfaces.

Package contents:

1 x Windshield Repair Injector
1 x repair resin
2 x Adhesive Seal
1 x Pedestal
5 x repair Film
1 x Razor Blade
1 x Instruction Manual

Tips:
This product is packed in opp bags.

A.Before curing: Operating in ultraviolet environment is forbidden.

lndoor or night operation is recommended.

B.Curing: Drop a drop of repair solution on the curing film, cover the damaged area,scrape the air bubbles with a blade,move to the sun for 10-30 minutes or use ultraviolet lamp instead until curing.

Divided into three layers:
It can be broken directly and take out the glass repair solution

DIY windshield repair  kit is designed to fill the air cavity with a strong penetrating adhesive that will  bone the loose glass and -restore the visibility,the patented design evacuates the air to fill the cavities with specially formulated liquid glass,that clears the distortion and bonds the loose glass preventing the damage from spreading 
NOTE:
A:Avoid using in direct sunlight -work in a shaded area
B:Do not work on a hot windshield ,park vehicle in a shade area and open windows to cool glass surface ,
C:A safe razor is required to remove components and finish repair
CAUTION:
Do not let resin come in contact with painted surfaces.

1.Clean Damaged Area 
CLEAN out any loose glass particles from PIT(hole caused by striking object)of  the break using Pin from injector.
Clean area surrounding break using a dry cloth or paper tower .
2.Mount Seal To Windshield


PEEL backing on one side of adhesive seal line up hole in seal with PIT(pointing tab upward ).press seal to glass 


Run fingers around seal to insure a  good bond 


3.Remove  Backing From Seal Mount Pedestal To Adhesive Seal 


Peel backing from top side of adhesive seal 
Line up pedestal with adhesive seal making sure tabs match up,press pedestal to glass .
Run fingers around seal to insure a  tight bond

4,Place Resin into Pedestal
Cut Tip off resin container to open stem,Place stem 1/4 inch into pedestal opening .
Slowly squeezing resin  tube and remove from redestal.


Wipe any excess resin 
from tip with cloth & save the empty container
5,Lock Plunger in Vacuum Position
Connect injector to Pedestal,hold injector with one hand ,pull plunger upward with the other hand .Lock plunger by engaging Lower notch in plunger witg spring clip
Release hands and allow device to remain in locked position Let sit for 10 Minutes


6,Fill injector with Air 
Take injector out from the pedestal ,make the plunger to its maxi .position put the injector back to the pedestal



7,move plunger to pressure 
hold injector  with one hand and ROTATE plunger releasing spring clip from LOWER notch
DEPRESS plunger downward ENGAGE UPPER notch with spring clip .
LET SIT FOR A MINIMUM of 20 MINUTES

8,Remove Pedestal from Glass
loosen outer edges of pedestal with a safety razor .once top part of pedestal and seal is bent away from glass surface,grip pedestal tab as shown slowly pull up until removed.
wipe and remove excess resin


9,PIT filling Procedure 
hold resin container in one hand and make ready the clear curing film in the other hand as shown,slowly squeeze resin container applying a drop of resin in PIT.
place clear curing film over PIT holding resin in the PIT.


10,Curing & Finishing 
Run safety razor lightly over clear film to vent out any air bubbles.


Note:Ultra Videt sun rays cure the resin, Park vehicle in direct sunlight for 15 minutes 
11 ,on hazy days ,park vehicle in sun light for minimum  off hour.


To Finish ,scrap off cured resin  and  clear film flush with the glass surface using safety razor