eBike Accessories
Motorcycle Parts- 0Cart
-
Your shopping cart is empty.
-
more items in the cart...
Cart Total: $0.00
Proceed to Checkout
|
Item specifics
Product Description
Features: Microwave Sensor: One Kick is a microwave sensor mounted on the inside of the rear and sends down microwaves to detect. Tail Box Control: If the inductor detects an effective kick action in the induction area, it will output the corresponding level signal according to the signal intensity to control the opening of the tail box. Convenient: After installing a kick, the owner can easily open the trunk of the car through the kick action, no longer for the hands of large items and feel inconvenient. Fitment: This product just fit the car with electric tail gate lift. Install: There is the enough space in the rear bumper for installing our sensor. Specification Material: Plastic, electric componebts Color: Black Power supply voltage: DC 5-18 V Starting time: about 2s Operating current: about 5mA Microwave working mode: intermittent Microwave duty cycle: 4.4% Operating temperature :-40-+85 ℃ Emission frequency: 24.125 0.125 GHz Protection grade: IP68 Extension wire connection method 1, black line (power negative) : lapping; 2. Green line (key line) : keep a good contact with one end of the test pen tower iron end and the line on the original rear door key socket. Press the original rear door button at this time, and the light of the test pen will be off.(diode "test pen) 3. Red line (positive pole of power supply) : connect the original car with 12V constant current; 4. White line (ACC) : keep good contact with one end of the tower iron of the test pen and the other end with the measured line. At this time, the original car key is pressed to ACC, and the light of the test pen will light up Note: After connecting all wires, wait 20 seconds for self-test and then test again Installation steps and precautions (post-installation) : 1. First, wipe the position to be installed on the inside of the rear. It is best to install the sensor in the middle of the rear of the car without leaving soil, dust and water 2. Aimed at the hole mark on the sticker and drilled with a screw of your own, noting that the direction is outside the screw cap; 3. When the screw is drilled into the about 1 cm, stop drilling, and place the holes on the left and right sides of the microwave sensor on the screw drilled. The white glue surface is the induction surface, and the induction surface must be downward to the ground 4. Press and hold the microwave sensor to continue to screw the screw to fix the microwave sensor. After tightening the screw, the white glue and the inside of the should be completely fitted, and there can be no gap in the middle to prevent the sediment from entering and affect the use effect. 5. If there are mesh, protrusion and other structures on the inside of the white glue on the module can not be completely fitted with the inside of the .The mesh, protrusion and other structures must be polished or filled with glass glue, otherwise the gap between the water and sediment will greatly affect the performance of the sensor. Package included: 1pc x Sensor Module 1pc x Probe Signal Cable 2pxs x Location Screws 1pc x Location Paper
Note:1.Due to the difference between different monitors,the picture may not reflect the actual color of the item. We guarantee the style is the same as shown in the pictures,,but not the same performance on different bodies as on the model.
1) We accept Paypal, Credit Card or Debit Card Payment, West Union, TT. All major credit cards are accepted through secure payment processor ESCROW. 2 If you can't checkout immediately after auction close, please wait for a few minutes and retry Payments must be completed within 3 days.
1) WORLDWIDE SHIPPING. (Except some countries and APO/FPO)
DHL UPS TNT FEDEX takes 3-7 days ,EMS takes 8-12 days.Post air mail need 2-8 weeks.But all of them are dependent on the country delivered to.
1) Buyer's early confirmation will be highly appreciated after receiving the items. |
