Important Notice:

This ebike waterproof controller conversion kit not include motor or battery.

If you need ebike motor, please see our recommed product below.

Package Include:

-One ebike waterproof controller can only be used in conjunction with motors with sensors. The KT controller 36V 48V is compatible with 250W 350W hub motors.

-One PAS sensor, KT pedal auxiliary sensor 12 signal

-An electric bicycle display KT LCD4 or LCD5.
(Only used with KT Controller)

-One pair of brake sensors or brake levers (decided according to the suit you choose).

-One thumb throttle.

-One 1T4 Waterproof cable to connect the LCD Display / brake / throttle (cable length is about 180cm).

Features and Specifications of Ebike Controller:

-Applicable to 250W 350W brushless hub motor
-Only supports hub motors with sensors
-36V 48V universal (supports two voltages at the same time)
-Square wave controller (high efficiency)
-Support ebike display KT LCD4 KT LCD5 or LCD3 LCD8.
-Support 36V or 48V lighting control

1. Mosfet: 6 mosfet
2. Working voltage: DC 36V or 48V
3. Rated current: 8A
4. Low voltage protection: DC30/40±0.5V
5. Maximum current: 17±1A
6. Speed setting: 1-4.2V
7. Size: 94*61*36mm

-Motor connector (9-pin Julet waterproof female)
-Main cable: 8-pin Julet waterproof female connector (suitable for Julet1T4 waterproof cable).
-Battery cable (bullet)
-PAS sensor connector: 3-pin waterproof female (Julet)

About Pedal Assist Sensor:

Type: Dual Hall PAS sensor.
KT display setting: C1 = 7.
Installation method: left.
Voltage: used with 36V and 48V controllers.
Magnets: 12 magnets.
Cable length: 90cm excluding sensors and connectors.
Connector: 3-pin Julet waterproof male connector.
Braking corresponding time: <0.001S.
Corresponding distance: 2-3mm.
Hall electrical life:> 20M times.

About Julet 1T4 waterproof cable:

Cable length: about 180cm, including connector.

Connector: Input 8-pin Julet waterproof male connector.

Output: 1:5 pin Julet waterproof female head (display)

2: 3 pin Julet waterproof female head (throttle)

3: 3 pin Julet waterproof male head (brake)

4: 3-pin Julet waterproof male head (brake)

Ebike Display KT LCD4:

KT LCD4 EBike LCD Display is for KT Series Controllers. It only fits KT series controllers. It is not suitable for other controllers.

1.Dimension: 19x54x10mm.
2.Supply voltage of 24V, 36V, 48V can be automatically identified and compatible;
3.Cable Length: About 21cm

Ebike Display KT LCD5:

KT LCD5 EBike LCD Meter for KT Series Controllers. It only fits KT series controllers. It is not suitable for other controllers.

-This electric bike display connector is not waterproof.It's 5pin waterproof male connector

-Cable length is about 40cm

-Work voltage:DC 24V 36V 48V

Ebike Display KT LCD3:

KT LCD3 EBike LCD Meter for KT Series Controllers. It only fits KT series controllers. It is not suitable for other controllers.

-This electric bike display connector is not waterproof.It's 5pin waterproof male connector

-Cable length is about 40cm

-Work voltage:DC 24V 36V 48V

Wuxing Brake Lever:

1.Connector: 3Julet waterproof female hend
2.Cable length: About 20cm
3.Application type: Mechanical Brake

Hydraulic Brake Sensor:

1.Connector: Julet waterproof 3 Pin male
2.Cable length:about 20cm
3.Application type:Hydraulic or Mechanical Brake

About Thumb Throttle

1. Connector: Julet waterproof 3-pin male
2. Cable length: about 20cm
3. Installation direction: right hand
4. Installation size: 22.2mm