|
Item specifics
Product Description
If you want to buy the motor only,please see this link: Motor only link  All the shipping way won't allow the item with gas go to there aircraft. So all the wheels are without gas to arrive to you. When you get it, please inflate the wheel firstly. The instrument has instructions, please ask us after receiving the goods if you need it.
Motor model: TX-10 Rated Current: 36V/48V Power: 350W,500W,600W,800W,1000W Pole: 15 Magnet height：38H Speed: 30-65KM/H Shaft length: 160MM Applicable models: 10-inch scooter Open Size: 110MM Outer diameter:168MM Width: 40MM Weight: 3.2kg Color: Black
1* 10 inch Hub motor 1* Front wheel 2 Set Tire( include the inner tube) 1* Controller 1* Accelerate instrument 1 Pair Brake lever 2* Disc brake set 2* Brake line
Test Report:
The hub motor:(Size/mm)
The controller lines:
LCD display wiring: 1. Red wire (D+): power supply positive input 2. Black wire (GND): negative pole of power supply 3. Blue line (DS): Controller electric door lock 4. Green wire (RX): communication reception 5. White line (TX): communication transmission Display function: Speed display, battery indicator, fault indicator, headlight indicator, cruise indicator, gear indicator, total mileage, single mileage Real-time voltage, running current, running time, start mode Parameter setting and definition: P01: Backlight brightness, level 1 is the darkest, level 3 is the brightest; P02: Mileage unit, 0: KM; 1: MILE; P03: Voltage level: 24V, 36V, 48V, default 36V; P04: Sleep time: 0, no sleep; other numbers are sleep time, range: 1-60; unit minute; P05: Power-assisted drive gear setting P06: Wheel diameter: unit, inch; precision: 0.1; P07: Number of speed magnets: range: 1-100; P08: Speed limit, the maximum operating speed of the motor P09: Zero start, non-zero start setting, 0: zero start; 1: non-zero start; P10: Drive mode setting 0 Power-assisted drive 1 Electric drive 2 Power-assisted drive Electric drive coexistence P11: Assist sensitivity setting 1-24 P12: Starting torque: range: 0-5, 0 is the weakest, 5 is the strongest; P13: Magnet type setting of booster plate 5 8 12 P14: Controller current limit value setting Default 12A range: 1-20A; (requires controller software support) P15: Motor drive signal percentage setting (to achieve the speed limit function of PO8) full speed is set to 100 P16: Instrument real-time cruise function 1 With this function 0 Without this function P17: Headlight synchronization function 1 Headlights and backlight do not light up after turning on 0 Headlights and backlight light up after turning on P18: Power-on password selection function 1 With this function 0 Without this function P99: One-key recovery function (in the P99 parameter setting interface, press and hold the MODE key for 5-6 seconds, and all parameters will be restored to the first Initial settings for the second boot) ODO: ODO clear (in the ODO parameter setting interface, first short press the MODE button and then long press for 5M-6 seconds until the number is zero, release The specific status of the fault content is as followsERRO 1: Motor failureERRO 2: Handlebar malfunctionERRO 3: Controller failureERRO 4: Power-off brake leverERRO 5: Undervoltage protectionERRO 6: Communication failure, the meter cannot receive the output of the controllerERRO 7: Communication failure, the controller cannot receive the output of the instrument
|
Accesorios para eBike
Piezas de motocicletas