ELM327 wifi/Bluetooth with PIC18F25K80 chip

Note:

Version A and B are same inside, different on the cover.
There are several options in the link, please choose the right device, according to your phone android or IOS.
- Bluetooth elm327 supports android system only, does not support IOS system, so if you have a iphone, please buy wifi ELM327.
- Wifi elm327 supports both android and IOS system.

Wifi ELM327 interface is able to detect and interpret obd2 / eobd protocols automatically. It also provides support for high speed communications and a low power sleep mode. It use AT commands to communicate with a host device (PC, notebook, for iOS). There are plenty of software packages available, which are fully compatible with this tool. Some of them have pretty useful features, such as engine running parameters monitoring, DTC reading and clearing, MPG meter, etc. You can even write your own software on a specified hardware platform if you wish, because the AT commands are fully documented and very well explained. This tool is only 2.7 x 1.25x 0.9 inches, and it comes with a 6 ft OBDII cable for easy installation. It also includes a power switch built-in to prevent the need for having to constantly disconnect your unit from the OBDII port. It is compatible with 1996 and later vehicles which are obd2 or eobd compliant. Connecting to your iPhone / iPod touch is made by WIFI connection in adHoc mode.

Features:

*Firmware Version V1.5 (Supports more protocols SAE J1850 than V2.1).
*With chip:PIC18F25K80 ,supports all elm327 fucntions,in program ELM327 identifier,it shows full functions.
It understand commands such as ATPPS and other.
The frequency of the crystal oscillator is 4mHz.
ELM327 wifi (7)

PIC18F25K80 chip  WIFI/Bluetooth Version  ELM327 V1.5 OBD2 OBDII code reader scanner

Note:

This elm327 usually can work on most new car with OBD 16pin Aadapter and 12V engine:

For USA Car brand,after 1996;

For Europe Car brand,after 2000;

For Japan/Korea Car brand,after 2002;

For Chinese Car brand,after 2005;

Fit for Chrysler ,Fit for Ford ,Fit for G-M ,Fit for Jeep;

Fit for Alfa Romeo, Fit for SAAB, Fit for Acura, Fit for Opel, Fit for Audi, Fit for Seat, Fit for Peugeot ,Fit for Renault, Fit for Bentley ,Fit for Skoda ,Fit for Daewoo, Fit for Benz ,Fit for Daihatsu, Fit for Land Rover, Fit for BMW ,Fit for Vauxhall ,Fit for Citroen, Fit for Volvo ,Fit for Fiat ,Fit for VW ,Fit for Ford ,Fit for Jaguar;

Fit for KIA , Fit for Isuzu ,Fit for Honda ,Fit for Mitsubishi, Fit for Hyundai  ,Fit for Dacia  ,Fit for Lexus ,Fit for Mazda, Fit for Nissan, Fit for Subaru , Fit for Suzuki, Fit for Toyota;

*For Lada/ VAZ/ UAZ car makes, please don't purchase If your car is before 2011.

*For Ssangyong car makes, please don't purchase If your car is before 2008.

*For Renault Dacia Logan car model, please don't purchase If your car is before 2009

If your vehicle does not fall into any of the above categories, look under the hood and try to locate a label that explicitly states that the vehicle was designed to comply with OBD-2 legislation.

Features:

*Firmware Version V1.5 (Supports more protocols SAE J1850 than V2.1)

*With chip: PIC18F25K80  ,supports all elm327 fucntions,in program ELM327 identifier,it shows full functions.

*It understand commands such as  ATPPS and other.

Multi-Protocol Support:

1.SAE J1850 PWM(41.6Kbaud)

2.SAE J1850 VPW(10.4Kbaud)