1. If you have any problem, please feel free to contact us first, we will try our best to help you.

2.Please"FOLLOW"our store, you will getExtra 1-3% Fans Exclusive Discount and Extra Couponsas our VIP customers.

There are 3 products in the link: KTM BENCH and KTM BENCH 32 IN 1 and KTM BENCH 67 IN 1
The modules supported by these two products are different, please pay attention to select the version you need.
KTM BENCH 32 IN 1 supports 32 protocols,KTM BENCH 67 IN 1 supports 67 protocols

The modules supported by the 2 products are as follows:

Bench 32 in 1:
12, 13, 14, 19, 20, 21, 26, 29, 30, 32, 33, 34, 35, 36, 40, 42, 46, 47, 52, 53, 54, 55, 57, 58, 61, 62,63,66,71,72,73,74

Bench 67 in 1:

1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,29,30,31,32,33,34,35,36,38,40,42,43,45,46,47,48,50,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68,69,70,71,72,73,74

ECU Programmer for BOOT and Bench and GearBox Read and Write

5 Reasons to buy BENCH 67 IN 1 New Version:

1.Support 67 modules that can be opened:

1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,29,30,31,32,33,34,35,36,38,40,42,43,45,46,47,48,50,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68,69,70,71,72,73,74

2.NO LIMITS of the car model and year + NO NEED disassemble ECUs Read and write for Bos** ECUs (Infin***'s chips) incl. flash and eeprom

3. LESS RISK to clone/copy ECUs Able to modify data or do chip tuning to achieve superior performance

4.EMT master board, Don't need pay  maual cost and month fee

5.BEHCH 67 IN 1 integrates three device function sets of FLASH, BEHCH, OBD 1.20 version

What is differences between BENCH , FLASH and OBD?

• BEHCHBoot is the latest ECU programming tool for ECU read and write via Boot mode or on bench.

• FLASHECU programmer can read the chip data, read & write ECU data. read transmission data etc. at a high speed.

• OBDprogrammer was born for reading chip data, reading and writing data of ECUs and a few types of gearbox. Read/write data by OBD.Supports most Japanese cars

In conclusion:

All programming tools above can be used for ECU read and write, but differs in ECU coverage and Read/Write method.

There is NO LIMITS of the car model and year when using BENCH to read/write data.

But if you have chips and gearboxes to read and write, you should have a FLASH. The bad is: disassembling is required. BENCH doesn't cover chips and gearboxes and OBD cannot not work good for gerabox Read/Write.

So, you'd better check the ECU/gearbox/chip before your purchase.
Check each car list on corresponding product page.

Module 1

Ford Focus 3

Ford Focus 3: 1.6L Sigma Ti-VCT 85/105/125PS (EMS2204)

Ford Focus 3: 1.6L, 2.0L PowerShift TCM (6DCT250)

Virtual reading, writing, checksum correction. VBF writing and VBF to BIN conversion is supported!

Ford Focus 3: 2.0L Duratec GDI Ti-VCT 150/170PS (MED17)

Ford Focus 3 ST: 2.0L Ecoboost GTDI 250PS (MED17)

Reading, writing, checksum correction.