LAUNCH X431 CReader 3001 Full OBD2 EOBD Code Reader Scanner

Why Choose LAUNCH CR3001

The CReader 3001 is specially developed by LAUNCH, which support all 10 modes of OBD II test for a complete diagnosis.

Featuring the color LCD, it enables users to read/clear DTCs, record and save data. The CReader 3001 is also very easy to use.

With built-in help menus and code definitions, diagnosing and repairing that dreaded Check Engine Light is now easier than ever!

Moreover, CReader 3001 also features the following bi-directional “special tests”: EVAP, O2 Sensor, I/M Readiness, MIL Status, VIN Info, and On-board monitors testing....

Launch CR3001 Support Language:

English , French , Russian , Spanish ,German, Italian ,Portuguese

Launch CR3001 Supports Life-time Free update , it update directly with computer , easy to use !

Turn Off "Check Engine" Light

Parts might cause your check engine light on include:
1. Gas Cap 2. Oxygen Sensor 3. Air Fuel Ratio Sensor 4. Mass Air Flow Sensor 5. Ignition Coils 6. Spark Plug Wires 7. Spark Plugs 8. Thermostat 9. EGR Valve 10. Evaporatative Emission Canister Purge Valve(EVAP) 11. Catalytic Converter.

If the engine light is not turned off in time
it will Cause Serious environmental pollution , Increased fuel consumption,Increased engine noise.Increased in temperature , ect.

Launch CR3001 supports Full OBD2 Function Diagnnosis

Reading Codes
Show the detailed description of the Diagnostic Trouble Code (DTCs)

Erasing Codes & Reset
Turns off Check Engine Light (MIL), clears codes and resets monitors.

Data Stream
Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.

I/M Readiness Status
Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.

Read Live Data Stream
Show the information of continuous data stream from a vehicle in live graphic (waveform) display.

View Freeze Frame Data
Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.

O2 Sensor Test
Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.

On-Board Monitor Test
Retrieves and displays test results for emission-related powertrain components and systems.

Read Vehicle Information
Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.

Component Test
Certain vehicle components can be actuated by commands sent from the scanner to test their operability

LAUNCH CR3001 Ehanced model 6 test , Help you figure out the problems .

LAUNCH CR3001 Support OBD2 protocols car :

1.SAE J1850 PWM(41.6Kbaud)
2.SAE J1850 VPW(10.4Kbaud)
3.ISO9141-2(5 baud init,10.4Kbaud)
4.ISO14230-4 KWP(5 baud init,10.4 Kbaud)
5.ISO14230-4 KWP(fast init,10.4 Kbaud)
6.ISO15765-4 CAN(11bit ID,500 Kbaud)
7.ISO15765-4 CAN(29bit ID,500 Kbaud)
8.ISO15765-4 CAN(11bit ID,250 Kbaud)
9.ISO15765-4 CAN(29bit ID,250 Kbaud

LAUNCH CR3001 supports Car List : (Note: CR3001 only Support 12V Gasoline& Diesel, Does not support 24V Truck )

American Car : from 2000 - now
for Chrysler , for Ford, for GM, For Jeep , for lincoln ,for Buick ,for Cadillac ,for Chevrolet , for Dodge , for HM...

European Car : from 2003 - now
for BENZ ,for SMART , for SPRINTER , for BMW ,for VW ,for SKODA ,for AUDI ,for OPEL, for Lamborghini , for PORSCHE, for Maybach,for Euro Ford , for LANDROVER , for Jaguar , for ASTONMARTIN ,for Bentley , for Rolls-Royce , for ROVER , for MINI , for VAUXHALL ,for DR , for FERRARI ,for FIAT ,for Abarth ,for LANCIA ,for Alfa Romeo , for Maserati ,for BUGATTI ,for PEUGEOT ,for CITROEN ,for RENAULT , for SAAB , for VOLVO , for OPEL，for GM，for GMSA , for Dacia , for SEAT..

Japanese/Korean Car: from 2006 - now
for HONDA ，for Acura ,for TOYOTA ,for SCION ，for LEXUS ，for MAZDA , for NISSAN ，for Infiniti ， for JPISUZU，ISUZU ， for TLISUZU for DAIHATSU , for SUZUKI , for MITSUBISHI ,for SUBARU , for SAMSUNG , for DAEWOO ,for SSANGYONG , for HYUNDAI , for KIA...

Chinese Car:from 2009 to now
for GREAT WALL, for HUACHEN, for GEELY, for DFHONDA, for LIFAN...

Russian Car: from 2012 to now
for GAZ, for VAZ ,for LADA, for IZH, for PAZ,for SeAZ ,for UAZ, for ZAZ...

How to use Launch CR3001 :

Step 1 : Connect CR3001 with car use obd cable .
Step 2 : enter Main menu of CR3001, choose the function that you want to do .

How to Update Launch CR3001 :

Step 1 : Download update tool from launch offical website , then install in your computer .
Step 2 : Connect CR3001 with computer use USB cable , pls install the driver well !
Step 3 : open update tool to Update , it will be ok .
(if you still do not know how to operate , please check video below )

The screen show of LAUNCH CR3001 :

LAUNCH CR3001 Packing List :

1pc main unit of CR3001
1pc usb cable
1pc User Manual