- 0Cart
-
Your shopping cart is empty.
-
more items in the cart...
Cart Total: $0.00
Proceed to Checkout
Your shopping cart is empty.
Cart Total: $0.00
Proceed to Checkout
Item specifics
Product Description
For Honda CMX 500Rebel2017-2019 For Honda CRF250L/M All YearsFor Honda Crossrunner All YearsFor Honda CTX700 (w/o DTC) 2014-2017For Honda Fury 2010-2018For Honda Interstate 2010-2016For Honda NC400X 2013-2015For Honda NC700 S/X 2012-2017For Honda NC750 S/X 2014-2018For Honda NT700V Deauville 2006-2015For Honda Sabre 2010-2012For Honda Stateline 2010-2017For Honda VFR800 interceptor 2005-2013For Honda VFR800X All YearsFor Honda VT400 (FI model) 2009-2014For Honda VT750C (FI model) 2007-2017For Honda VT750S (FI model) 2007-2009For Honda VT1300 (All) 2010-2016For Honda VTX1800 2005-2012For Honda XL125V Varadero 2007-2014For Honda XL700V Transalp (non-ABS) 2008-2014For Honda XL700V Transalp (ABS) 2008-2014For Honda XL1000V Varadero 2003-2012For Honda TRX ATVs (FI model) All YearsFor Honda CB300R 2018-2019For Honda GL1800 2005-2017For Honda CTX1300 2014-2015For Honda ST1300 2008-2015For Honda VTR250 2009-2014(If you encounter any questions, please be sure to contact me first, please do not leave negative comments first, I very much hope to answer your questions, thank you)For Honda CB500X VFR 800 CB1000R CB400SF CBR650F CB600F CB650F Motorcycle 1-6 Level Ecu Plug Mount Speed Gear Display Indicator Description:Condition:100% Brand NewColor of Light Source:Red/Blue/greenItem Name:Speed Gear Display IndicatorSize:4cm*4cm*4cm/1.57inch*1.57inch*1.57inchFeature:Shows current gear numberIndicates current gear from 1 to max of 6. as well as a neutral indicator.Detects the current gear faster than other gear indicators that use speedometer/tachometer signal.Display can be mounted anywhereInstallation:Find the RED,4-pole male diagnostic connector(DLC), usually near the ECU box,It may have a removable cap and may be partially covered by black tape.Steps:-You need to setup the module after installation. When ignition is turned on, the display counts backwards (6 to 1) indicating that the memory is clear. -Raise the rear wheel off the ground by using a stand, and start the engine in Neutral. (If you do not have a stand, you may setup the unit while riding. Find a long, straight road with light traffic.) the screen displays L, indicating that learning is started. accelerate through the handle throttle slowly -The display will blink “1”.Select first gear, release the clutch, and keep the RPM above idle speed. The display is blinking faster while the unit is learning the gear. -When the display shows “2”, select second gear. Repeat this process until all gears are thought (5 or 6). The unit is programmed and should indicate the gears correctly. Now, when ignition is turned on, the display counts forward (1 to 6) indicating that it is fully functional. (If there is an error in the learning process, please reset gear indicator, thank you) Rest:If some gears are not indicated correctly, please reset gear indicator.turn on the key switch of the switch lock. When the gear indicator shows 5.4.3, turn off the key switch of the switch lock immediately, and then turn on the key switch of the switch lock immediately. According to the above operation, turn on and turn off the key switch of the switch lock five times in a row to see if the reset is complete. Thank you |