|
Item specifics
Product Description
Differences of THINKSCAN Plus S2/S4/S7 THINKSCAN Plus S2： Why You Need THINKSCAN Plus S7? 1.Thinkscan Plus S7 Support to diagnostic ECM/ABS/SRS/TCM/BCM/AC/IC system errors, and delete the errors. Support 7 System Diagnostic Lifetime Free Free Engine system Diagnostic: You can diagnose the engine system via ecu obd2 port, support all 10 OBDII test modes, such as live data, O2 sensor test, component test and more;read and clear the engine error codes, find out the exactly problem, repair it, and turn off the MIL engine light. Free ABS system Diagnostic: Diagnosing an ABS problem should always start with a visual inspection of all brake components, next you will need to retrieve ABS codes to tell you where the problem is, and this is what this scanner does for you. Free SRS system Diagnostic: safety restraint system, is made up of impact sensors, a control module, and the airbags themselves, and this diagnostic device can detect every electronic parameter to check its health status. Chassis System(BCM) Diagnostic: Carry out fault diagnosis on body/frame/transmission system/steering system/brake system/driving system Free Auto Transmission System: AT is a set of transmission used to coordinate the engine speed and the actual speed of the wheel, which is used to give full play to the best performance of the engine. THINKSCAN609 obd2 scanner can read/clear codes and view live data retrieve the error information from AT Free AC & IC System  Support 28 Reset Services(Buyer choose 5 resets) 1.Oil Lamp Reset Service Allows you to perform reset for a new calculation of Engine Oil Life system once changed the oil. 2.EPB Electronic Park Brake Reset It is important in the maintenance of electronic braking system's safety and efficiency. 3.BAT battery service Allows the scan tool to evaluate the battery charge state, monitor the close-circuit current, register the battery replacement, and activate the rest state of the vehicle. 4.DPF Diesel Particulate Filter Reset Specially works for Diesel Particulate Filter system with DPF regeneration, DPF component replacement teach-in and DPF teach-in after replacing the engine control unit. 5.SAS Steering Angel Sensor Reset Helps clear the fault steering angle sensor memories and plays an important role in the steering angle sensor calibration. 6.TPMS Tire Pressure Monitoring System Reset Makes sense in displaying sensor IDs from the vehicle's ECU, inputting TPMS sensor replacement IDs and testing sensors. 7.IMMO Key Programming The unique car key programming and read pin code function, it is mainly used to disable the lost vehicle keys and program a new replacement key fob. 8.ABS Bleeding ABS brake bleeding to get a firm brake pad after air exhaustion after repair ABS pump system. 9.Sunroof Reset The sunroof needs to be reset when the sunroof control unit have communication problem or changed. 10.Suspension Reset Try reset electronic suspension air ride with the massage system close all doors koeo flip through messages system go to suspension reset or on off. 11.Gearbox (Transmission )Reset Procedure Reset Transmission Adaptive Learning DIY. Start the car and drive. Once you perform this procedure the Engine Control Unit (ECU) and Transmission Control Unit (TCU) will work together to learn how you drive by monitoring your driving pattern. After you follow this programming method of the TCU / ECU drive the car. 12.AFS Headlamp Reset 'AFS' means Adaptive Front lighting System (at night with the Bi-Xenon headlights) it swivels either side, pressing that button means they stay pointing straight ahead and don't turn when you turn the steering wheel. 13.Injector Coding Leaking injectors and some dead injectors can be missed even when an injector is disabled. Other problems with the ignition system and mechanical components also may not show an rpm loss when an injector is turned off. 14.Throttle Adaptation The throttle body is a tube containing a pivoting flat valve (butterfly) that is used to control the amount of air entering an engine. In an electronically fuel injected car, a throttle position sensor and air flow sensor communicate with the computer, which supplies the corresponding amount of fuel needed at the injectors. It must need re-learning throttle sensor position after clearing or repair. 15.Gear Learning The scan tool monitors certain camshaft position sensors signals to determine if all conditions are met to continue with the procedure for Engine running. 16.EGR Reset Reduce nitrogen oxides (NOx) in the exhaust gas and improve fuel economy at partial load. 17.A/F Reset This function is applied to set or learn Air/Fuel ratio parameters. 18.Adblue Reset(Diesel Engine Exhaust Gas Filter) After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required. 19.Airbag Reset This function resets the airbag data to clear the airbag collision fault indicator. 20.Coolant Bleeding Use this function to activate the electronic water pump before venting the cooling system. 21.AT Learning This function can complete the gearbox self-learning to improve gear shifting quality. When the gearbox is disassembled or repaired (after some of the car battery is powered off), it will lead to shift delay or impact problem. In this case, this function needs to be done so that the gearbox can automatically compensate according to the driving conditions so as to achieve more comfortable and better shift 22.Language Change This function is used to change the system language of the vehicle central control panel. 23.Nox Sensor Reset Nox sensor is a sensor used to detect the content of nitrogen oxides (Nox) in engine exhaust. lf the Nox fault is re-initialized and the Nox catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine Ecu. 24.ODO Reset a) ODO reset is to copy,write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual mileage. b)Usually when the mileage is not correct due to the damaged vehicle speed sensor or odometer failure, it is necessary to do ODO reset after maintenance. 25.Stop/Start Reset This function is used to open or close the automatic start-stop function via setting the hidden function in ECU(provided that the vehicle has a hidden function and supported by hardware). 26.Seat Calibration This function is applied to match the seats with memory function that are replaced and repaired. 27.Transport Mode ln order to reduce power consumption, the following functions may be disabled, including limiting the vehicle speed, not waking up the door opening network, and disabling the remote control key, etc.At this time, the transport mode needs to be deactivated to restore the vehicle to normal. 28.Windows Calibration This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window. Calificación media:5 ( 0 Comentarios )
Escribir un comentario
|
Accesorios para eBike
Piezas de motocicletas